AEM

Plug-in coupler for shaft lining adapter

Plug-in coupler for shaft lining adapter AEM

  • For the articulated connection of HD-PE pipes into ducts in accordance with DIN 4034 or DWA-A 157 together with the FRIAFIT adapter ASF/ASFL
  • With two elastomeric sealing rings as hinge for optimum compression
  • With water-swellable sealing ring Q for additional safety
  • Connection side to HD-PE pipe with open-wire technology for optimal heat transfer for use without holding devices
  • Safety technology
  • Level transition to chamber sole

Note:

Also available with NBR seals (handling of substances hazardous to water according to AwSV, application WHG e.g. grease and coalescence separators): Stock status 3.

Go back Data sheet

PE 100

Maximum permissible test pressure 0.5 bar to DIN EN 1610

Reference d d1 D L t Weight kg BX PU
680201 110 131 133 165 135 0,700 8 144
680202 160 187 193 225 135 1,900 8 64
680203 180 215 225 220 135 3,100 1 54
680204 200 247 250 220 135 3,500 1 56
680205 225 277 280 220 135 4,600 1 32
680206 250 277 280 220 135 2,500 1 32
680207 280 313 315 220 135 3,600 1 32
680208 315 354 355 220 135 4,350 1 24
680209 355 399 400 220 135 5,800 1 20
680210 400 449 450 220 135 8,300 1 12
680211 450 499 500 220 135 8,900 1 8
680214 500 559 562 220 135 11,050 1 8
1 680212 560 624 630 220 135 13,400 2 4
1 680213 630 709 710 270 135 22,400 1 3
1 with pre-heating technology for optimum gap bridging

Sealing rings made of material SBR

Alternatively: NBR seal (stocked status 3) available on request

Sewage pipe systems are high-value assets of a value which has to be maintained for a long time. Increasing demands on the public sewage system require materials which meet these criteria. HDPE sewage pipes have been fused for many years with the FRIAFIT HDPE sewage system tightly, frictionlocked and root-proof.

Areas of Application

The FRIAFIT-Sewage Insert Sleeve AEM is applied for the connection of HDPE pipes into concrete inspection chambers according to DIN 4034 in connection with FRIAFIT-Sewage Inspection Chamber Adapter ASF/ASFL.

Notes on processing

The AEM is pushed into the ASF Sewage Inspection Chamber Adapter ASF until it connects with the gutter, resp. to the stop (ASFL).

Fusion of pipe ends with FRIAFIT AEM Sewage Insert Sleeve takes place using FRIAFIT fusion – leakproof and longitudinally strong.

The HDPE pipe is prepared according to the general installation requirements (see also “Fitting Instructions” for the FRIAFIT-Sewage System). This involves removing the oxide layer and cleaning the pipe ends. It is then slid into the AEM; length of insertion = L or transition to the gutter (ASFL).

To compensate a larger annular gap (> 1 mm, max. 3 mm) between coupler and pipe, the pre-heating barcode can be used from d 560 (see instructions packed up with the coupler).

Good reasons for using the FRIAFIT-Sewage Insert Sleeve AEM

  • Jointing part at the inspection chamber in conjunction with FRIAFIT-Inspection Chamber Adapter (ASF/ASFL)

  • An elastomeric sealing in duplicate allows optimum anchoring to the FRIAFIT-Inspection Chamber Adapter (ASF/ASFL) according to DIN V 4034-1 and ATV-DVWK-A 157

  • Inspection chamber free from axial pipe stress due to push-fit connection

  • Sealing rings comply with DIN EN 681, resp. DIN 4060

  • Incl. the water swelling sealing ring Q which offers additional security

  • Exposed heating coil on inside of sleeve for a secure fusion of the HDPE-pipe

  • Barcode for fully automatic fusion with HDPE pipes from SDR 33 to SDR 11 having regard to the ambient temperature (temperature compensation)

Downloads